Gypsum Plaster cornice Fiberglass Mold/frame

Gypsum Plaster cornice Fiberglass Mold/frame

Arabic
English
Products Category
News

• FRP(fibreglass reinforced plas • The method of improve the stre • China get back in the plasterb • How to choose gypsum plaster c • Building gypsum powder in the

Contact Us

Name: Micheal
Tel: 0086 20 66692370
Fax: 0086 20 62614092
Mobile: 0086 135 7001 4940
E-mail: sales@gypsum-cornices.com
Add: Room 9-206, Dongpu Road 2, Tianhe Area, Guangzhou, Guangdong, China (Mainland) WHATAPPS:+86 13570014940 wechat:13570014940
MSN: micheal-62@hotmail.com Skype: micheal-62 点击这里给我发消息

Partners
youtube.com Glory gypsum plaster moulding drywall Glory gypsum
News

How To Fit A Plasterboard Ceiling

Author锛歮icheal Date锛7/13/2012 12:06:37 AM
 

Plasterboarding a ceiling is a satisfying if slightly awkward DIY job that can save you a fortune on labour costs.We show you how with this easy to follow step-by-step guide including a full list of materials and tools needed.

Plasterboarding an existing ceiling

It is possible to fix plasterboard over an existing ceiling, but you'll need to determine where the joists are first. For upstairs rooms this can be done by measuring the joist gaps in the loft. Downstairs you'll have to prod the ceiling with an awl or lift the floorboards in the room above. Mark the joist gaps on the wall with chalk and you're ready to go. The other option is to strip off the existing ceiling to reveal the joists.

MATERIALS NEEDED:

  • 50mm x 50mm sawn wood for noggings
  • Lengths of wood to help support plasterboard
  • 12.5mm plasterboard
  • 38mm drywall screws
  • Perforated plasterboard tape
  • Joint filler
  • Sand paper (120 grade)

TOOL LIST:

  • Tape measure
  • Rubber-bladed filler applicator or plastering trowel
  • Trestles and planks or alimunium platform to stand on
  • Dust mask
  • Goggles
  • Knife (Stanley type)
  • Electric screwdriver
  • Spirit level
  • Pencil
  • Wood saw

Fitting a plasterboard ceiling steps 1 and 2

1. For non-sloping ceilings you can get a pretty accurate area measurement of the ceiling by measuring the floor.Multiply the width of the room by its length (in metres) and this will give you a square metre figure. Plasterboard is commonly available in 2.4 x 1.2m (2.8m2), 1.8 x 1.2m (2.1m2) and 1.2 x .9m (1.08m2) sizes at most builders merchants and DIY stores.

2. Plasterboard needs to be well supported. If there is no wood between the joists where they meet the wall, nail in some noggings made up of 50mm x 50mm wood. You should also nail in noggings between the joists where the long edges of the plasterboard will fall (AS SHOWN). The end of the plasterboard sits half way across the joist to allow the next board to butt up to it.

Fitting a plasterboard ceiling steps 3 and 4

3. Starting from the corner of the room, position the first board. Lengths of wood can be used to prop up the board.

4. Use 38mm plasterboard screws to fix the board to the joists and noggings. Screws are a better bet than nails for renovation projects, where hammering can potentially disturb or damage the joists. Fixings should be made every 150mm. Keep fixings at least 13mm away from board edges that have been cut; 10mm away from factory-bound edges. Be careful not to drive the screws in too deep or you'll damage the board. Once the screw head dips just below the face of the board, stop tightening. Staggering the boards (NOT SHOWN) makes for a stronger ceiling and prevents any cracks that may develop in the filler from running the full width or length of the room. Leave a 3mm gap between boards: this helps the filler to get a good grip.

Fitting a plasterboard ceiling step 5

5. To cut the boards, measure and mark the board to be cut. Lay a spirit level along the line and use a sharp Stanley-type knife to cut through the paper. Bend the board the opposite way to the cut and then cut through the paper on the other side of the board. You should now have a very neat cut board.

Fitting a plasterboard ceiling steps 6 and 7

6. Once all the boards are in place, tape over them with perforated plasterboard tape.

7. Mix up the joint filler so that it makes a smooth, but fairly stiff paste. This filler is mixed by pouring a measured amount of water into a bucket and then adding the filler in powder form. Follow the instructions or you'll end up with more filler than youre ever likely to use.

Fitting a plasterboard ceiling step 8

8. Use a rubber-bladed applicator or, alternatively, a traditional metal plastering trowel to fill in between the joints and screw head dips. This wide-bladed applicator helps to feather out the filler so that there is only a tiny ridge to be rubbed down when its dry. Once you've finished filling, leave the ceiling to dry for 24 hours before lightly sanding down with 120-grit paper. The filler creates a very fine dust that is particularly unpleasant to be showered in, so open all windows and put on goggles, gloves and a good dust mask before you start this job.